640-822 Exam

Quality and Value for the 640-822 Exam

4cert Practice Exams for Cisco 640-822 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

Guarantee to Pass Your 640-822 Exam

If you prepare for the exam using our 4cert testing engine, we guarantee your success in the first attempt. If you do not pass the CCNA 640-822 Exam exam (Interconnecting Cisco Networking Devices Part 1(ICND1)) on your first attempt we will give you a FREE UPDATE of your purchasing fee AND send you another same value product for free.

Cisco 640-822 Exams (in EXE format)

Our Exam 640-822 Preparation Material provides you everything you will need to take your 640-822 Exam. The 640-822 Exam details are researched and produced by Professional Certification Experts who are constantly using industry experience to produce precise, and logical. You may get questions from different web sites or books, but logic is the key. Our Product will help you not only pass in the first try, but also save your valuable time.

640-822 Downloadable, Interactive Testing engines

We are all well aware that a major problem in the IT industry is that there is a lack of quality study materials. Our Exam Preparation Material provides you everything you will need to take a certification examination. Like actual certification exams, our Practice Tests are in multiple-choice (MCQs) Our Cisco 640-822 Exam will provide you with exam questions with verified answers that reflect the actual exam. These questions and answers provide you with the experience of taking the actual test. High quality and Value for the 640-822 Exam:100% Guarantee to Pass Your CCNA exam and get your CCNA Certification.
　
　
Exam : Cisco 640-822
Title : Interconnecting Cisco Networking Devices Part 1


1. Refer to the exhibit. A network technician is attempting to use HyperTerminal to configure a new router using the settings shown. What is the reason the technician is unable to connect to the router?
A. The bits per second should be set to 9600.
B. The data bits should be set to 6.
C. Parity should be set to mark.
D. The stop bits should be set to 2.
E. Flow control should be set to hardware.
Answer: A

2. Refer to the exhibit. Workstation A must be able to telnet to switch SW-A through router RTA for management purposes. What must be configured for this connection to be successful?
A. VLAN 1 on RTA
B. default gateway on SW-A
C. IP routing on SW-A
D. cross-over cable connecting SW-A and RTA
Answer: B

3. Refer to the exhibit. A network technician has added host A to the network. Host A cannot communicate on the network. A ping that is issued on the host to address 127.0.0.1 fails. What is the problem?
A. The router is not forwarding the ping packets to network 127.0.0.0.
B. The remote host at 127.0.0.1 is unreachable.
C. The default gateway is incorrect.
D. The IP address of host A is incorrect.
E. The TCP/IP protocols are not loaded.
Answer: E

4. Which line from the output of the show ip interface command indicates that there is a Layer 1 problem?
A. Serial0/1 is up, line protocol is up
B. Serial0/1 is up, line protocol is down
C. Serial0/1 is down, line protocol is down
D. Serial0/1 is administratively down, line protocol is down
Answer: C

5. Refer to the exhibit. What could be possible causes for the "Serial0/0 is down" interface status? (Choose two.)
A. A Layer 1 problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists.
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0/0 interface.
Answer: AD

http://www.4cert.com The safer.easier way to get CCNA Certification.